8 min read

Turn Planning Policy Into Massing Before You Design

Three documents, three different legal weights. Get that straight before you read a single page of any of them, because it determines which sentences you have to obey and which ones you can argue with.

The local plan is part of the statutory development plan. Section 38(6) of the Planning and Compulsory Purchase Act 2004 requires that applications be determined in accordance with the development plan unless material considerations indicate otherwise. That is the only one of your three documents with that status. A supplementary planning document is a material consideration — real weight, but the government's Planning Practice Guidance is clear that an SPD expands on adopted policy and must not introduce new policy of its own. A conservation area appraisal is lower still in formal terms: it's evidence, adopted or not. Its teeth come from elsewhere — Section 72 of the Planning (Listed Buildings and Conservation Areas) Act 1990 obliges the decision-maker to pay special attention to preserving or enhancing the character and appearance of the area, and the appraisal is what tells them what that character is.

So when the three conflict — and on a tight infill plot they will — the hierarchy is: plan policy first, SPD as interpretation of it, appraisal as the evidence that gives the heritage policy its content. An SPD that invents a number the local plan never authorised is arguable. An appraisal that describes a prevailing building line is not law, but ignoring it means you have to beat Section 72 on your own evidence. Know which fight you're picking.

Free Lesson

Interior Testing

Watch free

Free Lesson

Interior Testing

28:50 · from Architectural Design in Practice

Watch free

Read for Verbs and Numbers, Not for Meaning

You are not going to read 300 pages. Nobody does, including the officer. What you do instead is run the document like a database.

Open the PDF and search, in order: metres, m2, storey, height, ridge, eaves, separation, distance, frontage, building line, ratio, %, per hectare, coverage, amenity space, parking, shall, must, will not be permitted. Every hit goes into a list with its policy number. That takes about forty minutes and it gets you ninety per cent of everything in the document that can actually move a wall.

Then go to the policies map — the interactive one, not the PDF extract. That's where the constraints land on your plot rather than on the borough in general: site allocations, any height or density figure attached to a character area, the conservation area boundary, Article 4 directions, flood zones, TPOs. Most authorities now publish these as downloadable layers, and the heritage designations sit on Historic England's National Heritage List. Pull them into your base model as georeferenced linework on day one. A conservation area boundary that clips the rear third of your site is a geometric fact, and it should exist in the model before the first sketch does.

Hard, Negotiable, Rhetoric

Now score every clause you've extracted. Three buckets, and the verb usually tells you which one.

Hard. Contains a number, or uses must, shall, will be required, will not be permitted. Minimum separation distances, maximum heights in storeys or metres, minimum amenity space per dwelling, parking ratios, any space standard the council has formally adopted. These are dimensions wearing a disguise. Treat them as if a structural engineer handed them to you.

Negotiable. Should, will normally, is expected to, where appropriate. These bind unless you can show why the exception is better. They're winnable, but each one you break costs you evidence, drawings and officer patience — and you only have so much of all three. Spend them deliberately.

Rhetoric. Seek to, encourage, have regard to, high quality, respect the character of, sensitive and sympathetic. These constrain nothing on their own. They matter enormously at the point of refusal, because they're the hooks an objection hangs on, but they will never tell you where to put a wall. The mistake I see constantly in Part 2 portfolios and in young practices alike is treating the rhetoric as the brief and the numbers as paperwork. It's the reverse.

One caveat on the rhetoric pile: it tells you what the officer is worried about. A policy that bangs on about roofscape three times is a policy written after a row about a flat-roofed box. Keep it on the sheet, in a column of its own, as intelligence rather than constraint.

Turning Words Into Geometry

This is the bit nobody writes down. A clause is only useful once it has units.

"Respect the prevailing building line." Go to the survey. Measure the setback from back of footway to front face for the six nearest properties on your side of the street. You'll usually get a cluster and one outlier. The cluster is the building line; draw it as a line in the model and label it with the actual figure. Your front face sits on it or behind it. If you need to break it — a recessed entrance, a projecting bay — you now know by exactly how much, and you can test that against the neighbours who already break it. The phrase has become a dimension with evidence behind it.

"Respect the established roofscape." Three numbers: eaves height, ridge height, roof pitch, taken off the survey for both neighbours. Set your eaves within that range and the scheme reads as part of the street even if everything else is contemporary. Pitch is the one that catches people — measure it, don't guess it, because a Victorian terrace at 40 degrees and your 25-degree default will fight at the party wall junction forever.

"No unacceptable loss of amenity to neighbouring occupiers." Pure rhetoric until you pair it with two things. First, any separation distance in the SPD — say it gives 21m between facing habitable-room windows at two storeys. That's a hard constraint and it sets your rear building line before you've drawn a plan. Second, BRE's Site Layout Planning for Daylight and Sunlight, which gives you the 25-degree test: where an obstruction subtends less than 25 degrees to the horizontal measured from the centre of the lowest affected window, daylight is unlikely to be materially affected. Draw that section. It will usually tell you where the top floor has to set back, and it does it in minutes.

"Fenestration should reflect the proportions of the surrounding context." Take a straight-on photograph of three neighbouring facades — rectified if you can be bothered, eyeballed if you can't. Measure window width to height, and glazed area to total facade area. You'll get a range, something like 1:1.6 vertical proportion and 20–30% glazing. Those are now the brackets you design inside. If your facade lands at 45% glazing you haven't broken a rule, but you've just volunteered for an argument, and you should know you're having it.

Materials. The appraisal will name the prevailing material. In Liverpool, where our Architectural Design in Practice scheme sits, that's red brick — and as we say on the course, using brick does you no harm with the planners there. The nuance worth having is that the material is a licence, not a sentence. A corner building on a main spine road earns more latitude than an infill in the middle of a terrace, because the corner is already an event in the street. Spend your deviation where the townscape already expects something different.

A street elevation survey marked up with the prevailing building line, eaves and ridge heights of neighbouring properties, and a 25-degree daylight section line

When the Appraisal Says Nothing

Plenty of appraisals are twelve pages of photographs and a boundary. No materials guidance, no proportional analysis, nothing about roofscape. Officers still refuse schemes on all three.

What we do in that situation is write the missing evidence ourselves, using the structure of Historic England's own advice on conservation area appraisal and management: identify the character areas, the positive contributors, the prevailing materials and the key views, and record them as a short survey with photographs and measurements. Half a day's work. It does two things. It gives you defensible numbers where the council gave you none, and it means that at determination your analysis is the only analysis on the table. An officer with no appraisal to cite will cite yours.

The same applies to the draft plan sitting in examination while you're designing to the adopted one. The NPPF sets out how much weight emerging policy gets — how advanced the plan is, how many unresolved objections there are, and how closely it aligns with national policy. Read the draft, put anything that would make your scheme harder onto the sheet as a risk row, and ignore anything that would make it easier until it's adopted. Designing to a policy that hasn't survived examination is how you end up redrawing a scheme twice.

The One Page That Replaces 300

Everything above collapses into a single sheet. A row per clause. For a hypothetical infill plot it might read:

Source & clause What it actually says Geometric consequence Status
Local Plan H4 Max 3 storeys in this character area Envelope capped at 3 storeys; roof accommodation tested separately Hard
Residential Design SPD §4.2 21m between facing habitable windows Rear facade min 10.5m from boundary Hard
Local Plan D1 Development should reflect prevailing building line Front face at 4.2m from footway (measured, 6 properties) Negotiable
CA Appraisal p.14 "Unbroken red brick frontages with vertical sash openings" Brick primary material; window proportion 1:1.7–1:2 Negotiable
Local Plan D3 "High quality design that enhances the area" None Rhetoric
Emerging Plan DM12 Proposed 30% private amenity space Risk row — test but do not design to Watch

That sheet is the brief. It goes on the wall, it goes in the model as linework, and it goes into the design and access statement later almost verbatim, because you've already written the justification column.

Build the Box, Then Carve It

With the sheet done, the first massing study is nearly mechanical. Extrude the plot to the hard constraints — storey cap, separation distances, building line, daylight sections. That solid is your maximum envelope, and it is the only honest answer to "how much can I get on here". Then carve: step down where the context steps down, set back the top floor where the 25-degree line bites, break the mass where the plot rhythm of the street says it should break.

The method we teach is contextual before it's anything else — what is the site telling us, what's the prevailing character, where does the height diminish. Policy reading is simply the written half of that same question. The appraisal is the street telling you about itself in prose, and the local plan is the council telling you which bits of that it intends to enforce.

Do this before you sketch and the policy work stops being the thing you dread in month four. Do it after, and you will spend that month proving a shape you already fell in love with. One of those is design. The other is litigation with drawings.

Written by

Adam Morgan

Architectural Director, ArchAdemia

About the team

Free Lesson

Interior Testing

Want to see it for yourself? Watch "Interior Testing" free — the full lesson, no account needed.

New guides by email. Course releases, free templates and guides, and software tips worth stealing. One click to unsubscribe.